ICOM IC-7610

The new Icom IC-7610 HF/50 MHz base transceiver employs a RF Direct-sampling/digital up-conversion HF/6m transceiver with two independent, identical receivers. MAIN and SUB receivers that can operate independently on different bands and modes (emissions)

Below you will find the features and specifications.

Features

• Direct-sampling/digital up-conversion HF/6m transceiver with two independent, identical receivers
• MAIN and SUB receivers can operate independently on different bands and modes (emissions)
• SUB receiver tuning knob available by plugging RC-28 controller into front-panel USB-A port
• MAIN/SUB Tracking (simultaneous tuning) from main tuning knob (enabled by menu option)
• Each receiver front end has dedicated ADC, ADC driver/preamp, BPF group and "Digi-Sel tracking preselector
• Separate DSP/audio chains for MAIN and SUB receivers; binaural reception possible
• Separate AF/SQL controls and EXT SP jacks for MAIN and SUB receivers
• Independent MAIN and SUB spectrum scope/waterfall displays(can be stacked L/R or MAIN above SUB)
• Dual clock displays
• Headphone left/right mix can be turned on or off
• MULTI knob for easier operation (similar to IC-7300)
• ANT1 and ANT2 ports with switched hybrid splitter for user-selectable dual-antenna (e.g. diversity) or Dual Watch configurations
• RX ANT IN/OUT BNC break jacks switchable between MAIN and SUB receiver
• 10 MHz EXT REF I/O and Transverter I/O BNC jacks
• PGA has MAIN and SUB inputs (from ADC's) and outputs (to DSP's), and display data channel to display driver subsystem
• New low-phase-noise clock oscillator with ultra-low-noise clock source provides high target RMDR of 105 dB (1 kHz offset), 113 dB (2 kHz offset) and excellent transmitter phase noise performance (also check review october 2018 attached!)
• 100W MOSFET PA unit
• High-speed relay-type auto-ATU
• Ethernet LAN port supports internal RS-BA1 server as in IC-7851, IC-7700 (FW V2.0 & higher), IC-7800 (FW V3.0 & higher)
• LAN Output Select menu option for AF (baseband) or IF
• Multiple memory functions
• Two rear-panel USB-B ports for CAT control/PCM audio
• Two front-panel USB-A ports for USB stick, mouse, RC-28 controller, keyboard etc.
• SD card slot for data capture, record/playback, firmware upgrade etc.
• Firmware upgrade via SD card or USB stick
• External meter and keypad jacks on rear panel
• 7" (diagonal) high-definition touch-screen display
• Independent MAIN and SUB real-time FFT spectrum scope/waterfall displays with high dynamic range (100 dB)
• Screen image capture to SD card
• Scope/waterfall windows can be stacked side-by-side or MAIN above SUB
• Multi-purpose real-time audio scope and FFT audio spectrum analyzer
• Rear-panel DVI-D port for external video display
• Large RAM reserve for future firmware expansion

Operating refinements

- Mute band by pressing corresponding volume knob
- Mic DC bias can be disabled for dynamic mc
- Keyer memories can use F1-F8 on keyboard
- Can record and capture directly to USB drive or SD card
- Adjustable independent beep tones for the main and sub bands from 500-2000Hz

Specifications

Frequencyrange	:	Rx 0,030 tot 60,000 MHz | Tx 135.7 kHz to 137.8 kHz (CW mode) -1,800 tot 1,999 MHz - 3,500 tot 3,999 MHz - 7,000 tot 7,200 MHz - 10,100 tot 10,150 MHz - 14,000 tot 14,350 MHz - 18,068 tot 18,168 MHz - 21,000 tot 21,450 MHz - 24,890 tot 24,990 MHz - 28,000 tot 29,700 MHz - 50,000 tot 54,000 MHz Modification is required for TX 60 meters; upon purchase, on request this modification can be performed by us free of charge)
Modes	:	USB, LSB, CW, RTTY, PSK31, AM, FM
Output	:	SSB, CW, RTTY, FM 1-100 W | AM 1-25 W
Number of channels	:	101
Frequency stability	:	< ±0,5 ppm
Antennatuner	:	automatic antennatuner included
Power supply requirement	:	13,8 VDC ±15 % (neg. ground)
Power consumption	:	TX max. 23,0 A | RX max. 3,5 A | Stand-by 3,0 A
Antenna connector	:	2x SO-239 (50 Ohm) | 1x BNC (RX only)
Dimensions	:	B 340 x H 118 x D 277 mm (housing only)
Weight	:	ca. 10 kg